Archive

Archive for the ‘Major Wing Sections’ Category

Spar/Rib Match Drilling Complete

August 23rd, 2012 No comments

Match Drilling Done

After the assembly of the left wing spars/ribs last night, I was anxious to get the match drilling done on it. I pulled out the #30 reamer and went to town on the spar attach holes. There are several holes in the ribs for the wing walk area that require a drill over the reamer because they are new and do not line up with the pre-punched holes in the ribs/rear spars. I am sure this was done at Vans to save production time/cost on the ribs. No big deal, you simply have to drill them and abandon the punched holes. The same applies to the first two leading edge ribs outboard of the tie-down block. I was able to match drill all the ribs for the right wing and then disassembled it. I was actually sad to see it apart. So was my son who ran out to the shop too late to see it all together. Oh well, it will be back together soon enough.

I then moved on to the left wing and repeated the process. Assembled, match drilled, and disassembled. I then deburred all the holes on the ribs and spars.

The night ended with the start of scuffing the ribs for primer. I made it through eight ribs before I ran out of Scotchbrite pads and will power. I will purchase some more pads tomorrow and hopefully be able to get the rest of the ribs scuffed this weekend. Then I can prime the ribs, assemble permanently, and hang the wings in the stands [that are being sandblasted/painted by a neighbor as we speak]. Despite the pain of rib prep, I am excited to be making progress again.

Categories: Major Wing Sections

Mindless Deburring, then Some Fun Progress

August 22nd, 2012 No comments

Now the fun really begins!

I was able to get out to the shop tonight. I tackled more mindless deburring on the corners and small tabs of the main ribs. Thank goodness for the second season of 24 playing on Netflix on the shop computer to keep my mind from actually realizing the monotony. I think it took me nearly four hours. However, once I was done, I had a pile of ribs that could be assembled in concert with the spars and prepped for match drilling. I figured what the heck, why not cleco the ribs to the spars on at least one wing and then call it a night. So that is where I left the project as evidenced by the above photo. After all the deburring I have been doing, it was neat to finally see a structure.

I still have the same mindless deburring to do on the leading edge/fuel tank ribs, but I will save that for later to break up the boredom.

The “Lightening Hole” Shot

It seems that every builder log I see, there is a picture of all the lightening holes of a wing together. I figured why buck the trend. So here you have it folks! It actually is pretty cool to see.

I hope to have the match drilling complete on the spars and ribs done soon. Then it will be the endless prep for primer. It is starting to really look cool. I can’t wait to get these assemblies in the stands to start getting skins on them.

Categories: Major Wing Sections

Ribs ALL Straight and Fluted

August 15th, 2012 No comments

Ahhh…Flanged and Fluted

Not much to report other than all the ribs are now straight and fluted. A little more spot deburring and these puppies will be ready for some fun. I guess I had better get my wing stands ready for use.

Categories: Major Wing Sections

Wing Rib Prep Continues

August 9th, 2012 No comments

Half Prepped…

OK, I am back from Oshkosh. I logged 15.5 hours in a RV-6. I saw tons of completed airplanes, so it was time to use all that fun as motivation to get back to work on mine. I am beginning to appreciate why many builders I talk to say that the rib prep was one of the most unpleasant tasks. It really is. I had done a major portion of the deburring earlier last month or so. I have to get all the little corners and nose portions of the leading edge and tank ribs still. I figured I would break up the deburring and straighten the flanges and flute the ribs, then go back to hit the rest of the deburring.

Per the RVator…My Version

My wife had some church visits to do last night, so I grabbed my nifty handmade flange straightener [described here] and fluting pliers and a stack of ribs and ran in the house so I could tend the kids and knock out some work. I found that my tool works great. I clamped it to the kitchen counter and went to town on the tank and leading edge ribs for the right wing. Once I was done straightening the flanges of each rib, I then fluted the flanges. By the last rib, I was straightening and fluting a rib in 5 minutes or less. The back and forth of the straightening and fluting broke up the monotony.

Once the leading edge ribs were complete, I knocked out the right wing main ribs. After about 4.5 hours, I was done for the night. I did have to make one change to the flange straightener. The block holding the arms loosened up a little with all the use, so I undid the screws and broke out the Gorilla Glue and glued it down and re-attached the screws. Other than that, I am glad I made it. I think it saved some good time and produced a great result.

I decided not to flute the W-408 rib just yet as it is not pre-punched and will work on it once I can mark out where the rivet holes will end up. The W-408 is what ties the leading edge and the tank together in the middle of the wing. There is a strip of aluminum that goes between this rib and the leading edge skin that also supports the outboard edge of the tank and ties it all together. Once I am closer to getting this rib put in assembly, I will flute it.

I get to camp with my oldest son this Friday, so I hope to hit the other half of the ribs straightened and fluted on Saturday and then finish up the deburring. I hope I survive rib prep. Once done, the real fun with the wings begins because you start really making something appear from the parts…WINGS!

Categories: Major Wing Sections

Rib Prep Begins

May 28th, 2012 No comments

Drilled and Deburred Holes, Now for Edges.

Happy Memorial Day!!! Thanks to all those that have and are serving for our freedoms!

I was able to get to the shop after a family BBQ. It was time to start some rib prep. I began by taking my angle grinder with a 1″ Scotch Brite wheel and deburred all the interior lightening holes. It went pretty fast.

I then opened up the tooling holes in the forward portion each of the aft ribs for accessories. In the left wing, I opened both the upper and lower holes to 3/8″ and in the right, just the lower tooling holes.

I continued and made a paper template to drill the 3/4″ holes in the ribs for a conduit that will run root to tip. I marked all the ribs and used the step bit on the drill press and knocked out all the holes. I backed the rib with a chunk of 2X4 and each came out nice and clean.

Next up, I deburred the new holes and the tooling holes I had opened up. That is when I had a “head slap” moment and realized I had made a stupid mistake. Can you spot it?

Times up! I drilled the 3/4″ holes aft of the stiffening bulge instead of forward…doh! I sent off an email to Van’s and admitted my folly and asked if I now needed to buy all new ribs. They replied with assurance that my location would pose no problems and to build on. Whew!

Structurally my hole would have no impact any greater than where it should have gone. The biggest concern is if it will interfere with the push rods for the ailerons. They actually give better clearance to the main push rod and no difference in clearance to the aileron push rod than had I put them forward of the stiffening bulge as recommended by Van’s.

Dodged that bullet!

Here is the projected plan for all the holes in the ribs.

Left Wing:

Conduit 5/8″ inner diameter:

  • Landing Light (LED – Low Power) In Leading Edge
  • Strobes (LED – Low Power) In Wing Tip Recess
  • Nav Lights (LED – Low Power) In Wing Tip Recess
  • Wig-Wag/Taxi Light (LED – Low Power) In Wing Tip Recess

Upper 3/8″ Hole with bushing to 1/4″ inner diameter:

  • Advance Flight Systems AOA Kit A
  • Stall Warner wire
  • Pitot Heat wire

Center 7/16″ Hole with bushing to 1/4″ inner diameter:

  • Pitot (5052-0 1/4″ OD 0.035″ wall aluminum tube) hard line to the root of the wing. SafeAir1 pitot line from there to instruments/AHRS.

Lower 3/8″ Hole with bushing to 1/4″ inner diameter:

  • Open for future need for Com/Nav/Marker antenna in wing tip or other accessory.

Right Wing:

Conduit 5/8″ inner diameter:

  • Landing Light (LED – Low Power) In Leading Edge
  • Strobes (LED – Low Power) In Wing Tip Recess
  • Nav Lights (LED – Low Power) In Wing Tip Recess
  • Wig-Wag/Taxi Light (LED – Low Power) In Wing Tip Recess

Center 7/16″ Hole with bushing to 1/4″ inner diameter:

  • Auto Pilot Roll Servo Wiring
  • OAT Probe Wire

Lower 3/8″ Hole with bushing to 1/4″ inner diameter:

  • Open for future need for Com/Nav/Marker antenna in wing tip or other accessory.

Hopefully that is enough and insures that no noise is introduced into any of the systems. High wattage lights were/are traditionally where most noise is introduced, so by separating them from any potential com/nav antenna wires should help eliminate this problem. That and the LED lighting being so low in wattage, I should be OK.

Next up, flange deburring….yippeee!

 

Categories: Major Wing Sections

Rib Sorting

May 20th, 2012 No comments

Oh the Work Required

Nothing to see here. I sorted the ribs per the plans to segregate them into stacks for each wing. The work to get to using these is extensive and daunting.

  1. Deburr lightening holes, flanges, corners, accessory holes.
  2. Straighten Flanges to 90°
  3. Flute to straighten the ribs
  4. Drill for conduit and accessory locations
  5. Scuff
  6. Prime
  7. Use

I hear the first 3 steps take hours each. Oh the fun to come.

Categories: Major Wing Sections

Rear Spars Riveted

May 19th, 2012 No comments

Rear Spar Doublers Riveted

Not too many pictures, I spent the day doing “Honey Do’s” and then got to smashing rivets. I was able to get all the rivets that can go in now done. The open holes that remain are for ribs or other brackets that will come later. I love it when you can smash parts with rivets. Means you can move on to something else.

I even got my wife to smash a few with the pneumatic squeezer. I hope to have her help more as the tasks and her time permits. Shop gets brighter when she comes to visit. 🙂

Categories: Major Wing Sections

Rear Spar Parts Primed

May 18th, 2012 No comments

I was able to prime all the rear spar parts tonight and clean up the shop for riveting tomorrow. No pictures.

Categories: Major Wing Sections

Left Rear Spar Work Continues

May 17th, 2012 No comments

Left Spar Doubler Hole Matching Begins

Tonight task was to repeat the processes done on the right spar on the left. Here you can see the center doubler clamped in the vice and ready to sand out the hole for the aileron push rod to exit. Instead of filing this one, I simply used a course grit Dremel sanding drum to get close to the line. It went much faster, but really chewed up the drum fast. Once close to the line I mated it up with the spar and finished it off as I did with the right spar.

After Some Dremeling

Here it is after the sanding drum and ready to be attached to the spar. The one caution I offer with the Dremel is that it takes material faster than a file and may allow one to get carried away. I sanded a little too much out on the right side of this hole between the upper and lower radii. Nit too bad, but a little off.

Ready to Prime

Once the left doubler fork, and outboard spar doubler were match drilled and dimpled, I scuffed all the parts for priming. I also dimpled the skin attach holes on all the holes where the spar forks would make it difficult to get to later as well as where all the doublers were where dimpling would be hard due to the double thickness at these locations.

The rear spars are now ready for priming. I hope to do that tomorrow so I can rivet the parts together on Saturday.

Categories: Major Wing Sections

Right Rear Spar Work Continues

May 16th, 2012 No comments

Match Drilled Right Rear Doubler

Tonight I continued the rear spar work by match drilling the doublers. I read on several builder sites about the furthest outboard holes on these doublers and the need to countersink them for flush rivets. The reason flush rivets are needed here is because an aileron bracket goes over the top. I felt the doubler was too thin to safely countersink. Other builders felt the same. I prefer the stronger joint that is made by dimpling the holes. This is an acceptable modification per Van’s as well. I simply have to remember to dimple the end rib holes as well. This will leave all the material thickness behind the aileron bracket that will be attached later. It may be overkill, but it is my plane.

Holes done for Right Aileron in Spar and Doubler

Another thing that has to be done is matching the aileron push rod exit in the center spar doubler. I clamped the doubler tight against the spar, match drilled and clecoed it on, then traced the hole dimensions onto the doubler. I then removed the doubler and used my step drill bit to remove a majority of the hole material. Then I clamped the doubler into my bench vise and filed the hole just shy of the trace line. Once close, I clecoed the doubler back onto the spar and finished the hole with my Dremel and sanding drum until they were an exact match.

Once the holes were matched, I then put a Scotch Bright wheel in the Dremel and polished the holes together. They turned out great and took about 15 minutes for this spar.

Right Rear Fork Match Drilled

Next up was match drilling the doubler fork on the inboard end. Nothing special here, just hit every hole with a bit.

It was late so I called it a night.

 

Categories: Major Wing Sections

More Main Spar Work

May 15th, 2012 No comments

AP Servo Bracket Installed on Right Spar

A few things showed up in the mail today. One of them was the the TruTrak autopilot servo brackets I was able to get from SteinAir. As I understand it, they typically do not sell the brackets sans the servo, but they accommodated me. I had a few minutes so I installed and torque sealed the bolts through the bracket onto the right spar. Now when I do buy the autopilot once I settle on the EFIS/AP combo, I simply need to bolt it in to the ready bracket.

I spent some time cleaning up the bench and shop to start work on the rear spars with less clutter.

Categories: Major Wing Sections

The Little Details

May 9th, 2012 No comments

Cleaveland Tie Downs...After Polishing

Since I tapped the tie down blocks, I figured I should test them with some tie down rings. Van’s does not supply them in the kit. I think because they are an easy to source local item for standard forged 3/8″ eye-bolts. I went to my local Fastenal and looked at them. They seemed very ugly to me. You spend all this time building a nice looking plane to have nasty looking eye bolts hanging off the wings? I remembered once that Cleaveland Tool sold some VERY nice looking stainless steel machined tie downs. While not as cheap as standard eye bolts, they are much better looking. I needed to order some other tools anyway, so I tossed three of these in my order. I figure if I go tail wheel, I can have a spare. If I go nose wheel, I have enough.

They arrived today and they are a thing of beauty. The machining is amazing. The finish however was simply satin. I have polished metal before and figured, I can get these to look REALLY good. My wife had church work to do, so I had all the kids come out and enjoy the weather while I tossed my buffing wheels into the drill press and started to polish them. The finish was so nice that it really only took a little buffing to bring out the shine. Near the bolt part, the machining left small lines in the surface that I hit with some 600 grit wet/dry sandpaper. Once sanded, I simply buffed again.

Now that they are polished to a mirror shine, they look like they belong on a nice plane. It may seem overkill, but little details can make the difference. It was the only thing I had time for anyway.

Categories: Major Wing Sections

Rear Spar Work Begins

May 2nd, 2012 No comments

Marking the Doubler for Trimming

I got out to the shop for a little bit after work and started the rear spars. First task is to trim the doubler forks and doubler plates that attach to the fuselage and spar. This apparently is only required for the RV-7 and RV-7a’s. The 7 and 8 share the same wing with a few tweaks. These are 0.040″ parts, so cutting them is not easy. My band-saw did make it easier and I was able to trim close to the line, run over to the 12″ disk sander and sand them closer, and then finally hit it with the scotchbright wheel. The layout was not so easy as the plans use extended lines drawn from the part itself. I simply traced the part onto some paper, superimposed the same lines from the plans onto the paper and then transferred the marks back to the part and then cut. I then used the first cut one as a template for the rest.

As a side note, Van’s does appear to have a full scale drawing in the plans of this trim, but it is not sent until the fuselage kit. Seems a little silly. Van’s should move that drawing to some empty space on one of the plan sheets for the wings. Thank goodness for preview plans however.

All Trimmed and Cleaned Up

Here are the parts after trimming and deburring them. It was then time to debur all the remaining edges. For this, I pulled out a file and the bench vice. I then hit them with the scotchbright wheel on my grinder and then completely buffed them with a maroon scotchbright pad. They have to be primed anyway, might as well get them ready for it now.

Ready to Match Drill

Once buffed, I clecoed them in place on the inboard side of the rear spars. They are ready for match drilling. At this point, it was time to call it a night.

Categories: Major Wing Sections